Agilent-technologies J3972A Manuale Utente Pagina 51
- Pagina / 189
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Local Terminal Configuration
Using a Local Terminal
31
NOTE
If the Token-Ring telemetry interface is installed, you can configure either the
Fast Ethernet interface or the Token-Ring interface as the telemetry interface. The
Fast Ethernet interface comes from the factory configured as Telemetry and the
Token-Ring interface comes configured as Monitor/Transmit and is disabled.
“Disabled” in this case means that the interface does not function at all, not as a
Telemetry port nor as a Monitor/Transmit port. If you configure the Token-Ring
interface as Telemetry, the Fast Ethernet interface automatically becomes
configured as Monitor/Transmit and is disabled.
Port Type Press
2
and select the port type as Telemetry. Making this
configuration change will disable the Ethernet telemetry port
(port 1). You can select either the Token-Ring or the Fast
Ethernet interface (but not both) as the telemetry port. The
telemetry port does not maintain network statistics for the
Token-Ring interface. The telemetry interface only allows the
retrieval of ATM network statistics. Refer to “Fast Ethernet
Telemetry Interface Configuration” on page 25 for
information on configuring the Fast Ethernet interface. The
probe must be configured with exactly one telemetry port.
IP Address Press
3
and enter the IP address for the probe. If the IP
address is 0.0.0.0, the probe will transmit Bootp Requests
for configuration information (including IP address) over the
network. This does not apply to ports configured as Monitor-
Only.
Default Gateway Press
4
and enter the default gateway IP address for the probe
IP Address (optional).
Subnet Mask Press
5
and enter the subnet mask for the probe.
Token-Ring Press
6
to modify or view the network speed setting.
Speed The default configuration is set to 16 Mbps network speed.
You can enter values of 4 or 16 for 4 Mbps or 16 Mbps
respectively or enter Auto to automatically sense the ring
speed.
- Agilent J3919A and J3972A 1
- OC-3 ATMProbes 1
- Consumer Warranty Statement 2
- Operating Restrictions 4
- Safety Information 7
- Conventions Used in this Book 9
- Trademarks 10
- Printing History 11
- Additional Help 11
- Contents 13
- Introduction 21
- Figure 1-1: The Probe 23
- Probe Overview 25
- Supported MIBs 27
- Management Stations 28
- Access Security 28
- Status LEDs 30
- Figure 1-3: Front Panel LEDs 31
- Token-Rin 32
- CONFIG Button 33
- Included Parts 34
- Optional Accessories 34
- Local Terminal Configuration 35
- Using a Local Terminal 39
- Agilent J3919A 40
- Agilent J3972A 40
- Modify/View Security Values 44
- Modify/View Interface Values 45
- Display Interface Summary 56
- Installation 61
- Selecting a Location 63
- Installing the Probe 64
- Table Installation 65
- Rack or Cabinet Installation 65
- Wall Installation 67
- Connecting the Probe 69
- Connectin 71
- to Token-Rin 74
- Telemetry Networks 74
- Figure 3-10: OC-3 System 78
- Bypass Mode 80
- Direct Connection 81
- Modem Connection 81
- Install the Probe’s Modem 83
- Data Switch Connection 86
- Starting the Probe 88
- Verifying the Installation 89
- Out-of-Band Troubleshooting 90
- Ethernet Telemetry Interface 90
- OC-3 ATM Troubleshooting 91
- Bootp Server type 96
- HP Sun PC 96
- Bootp Server Configuration 100
- Bootp Server Setup on a PC 101
- Using Novell NetWare 104
- Configuring the Bootptab File 107
- Tag Description 108
- Server Verification Process 109
- Example Bootptab File 110
- Probe Operation 111
- Restarting the Probe 113
- Cycling Power 115
- Cold Start 116
- Download New Firmware 119
- Terminal 126
- Xmodem Download of Firmware 131
- Cables and Connectors 135
- OC-3 ATM Interface Cables 137
- Token-Ring Cables 138
- Serial Port Interface Cables 139
- Cable Connector Pin-Outs 140
- Modem End 141
- 25-pin Male 141
- Probe End 141
- Terminal/PC Probe 142
- UTP Network Connector Pin-Out 143
- STP Network Connector Pin-Out 144
- Specifications 145
- Software Standards 147
- Dimensions 147
- Power Requirements 147
- Environment 148
- Storage Temperature 148
- Operating Non-Operating 148
- Protocol Encapsulation 149
- Probe Memory Allocation 150
- Glossary 153
- Numerics 181
Prodotti e manuali riguardandi Hardware Agilent-technologies J3972A
Hardware Agilent-technologies N2620A Manuale Utente
(279 pagine)
(279 pagine)
Hardware Agilent-technologies 85225F Manuale Utente
(148 pagine)
(148 pagine)
Hardware Agilent-technologies N9340A Manuale Utente
(161 pagine)
(161 pagine)
Hardware Agilent-technologies N2610A Manuale Utente
(248 pagine)
(248 pagine)
ASCOM OFFICE 130PRO manuals
Owner’s manuals and user’s guides for Telephones ASCOM OFFICE 130PRO.
We providing 3 pdf manuals ASCOM OFFICE 130PRO for download free by document types: Operations Instructions, User Manual, User's Guide
Commenti su questo manuale