Agilent Technologies E1345A Manuale Utente Pagina 48
- Pagina / 93
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Relay Multiplexer Command Reference 49
Parameters Parameter Types. The following table contains explanations and examples of
parameter types you might see later in this chapter.
Optional Parameters. Parameters shown within square brackets ([]) are optional
parameters. (Note that the brackets are not part of the command and are not sent to
the instrument.) If you do not specify a value for an optional parameter, the
instrument chooses a default value. For example, consider the
ARM:COUNt? [<MIN|MAX>]
command. If you send the command without
specifying a parameter, the present
ARM:COUNt value is returned. If you send the
MIN parameter, the command returns the minimum count available. If you send the
MAX parameter, the command returns the maximum count available. Be sure to
place a space between the command and the parameter.
Linking
Commands
Linking IEEE 488.2 Common Commands with SCPI Commands. Use a
semicolon between the commands. For example:
*RST;OUTP ON or TRIG:SOUR HOLD;*TRG
Linking Multiple SCPI Commands. Use both a semicolon and a colon between the
commands. For example:
ARM COUN 1;:TRIG:SOUR EXT
SCPI Command Reference
This section describes the Standard Commands for Programmable Instruments
(SCPI) commands for the multiplexer modules. Commands are listed alphabetically
by subsystem and also within each subsystem.
Parameter
Type Explanations and Examples
Numeric Accepts all commonly used decimal representations of numbers
including optional signs, decimal points, and scientific notation.
123, 123E2, -123, -1.23E2, .123, 1.23E-2, 1.23000E-01. Special
cases include MIN, MAX, and INF.
Boolean Represents a single binary condition that is either true or false.
ON, OFF, 1, 0.
Discrete Selects from a finite number of values. These parameters use
mnemonics to represent each valid setting.
An example is the TRIGger:SOURce <
source> command
where source can be BUS, EXT, HOLD, or IMM.
- *E1345-90005* 1
- Contents 3
- 2 Contents 4
- Contents 3 5
- 4 Contents 6
- Safety Symbols 8
- WARNINGS 8
- Documentation History 8
- Declaration of Conformity 9
- Getting Started 10
- Getting Started 13Chapter 1 12
- • specify the card number 13
- • specify the channel number 13
- Getting Started 15Chapter 1 14
- SCPI Command 15
- Format Used in This 15
- Initial Operation 16
- Chapter 2 18
- Warnings and Cautions 18
- Connecting Field Wiring 19
- Wiring a Terminal Module 20
- Connecting the Analog Bus 21
- Setting the Card ID 22
- Using the Scanning 23
- Voltmeter 23
- Configuration 23
- Connecting User Inputs 28
- Chapter 3 30
- Using This Chapter 30
- Multiplexer Commands 30
- Example: Connect 31
- Channels 02 and 09 to 31
- Making Measurements 33
- Channels 02 and 10 to 34
- Tree Terminals for 4-Wire 34
- Ohms Measurements 34
- Example: Making Voltage 35
- Measurements by 35
- Scanning 35
- (E1344A/47A Modules Only) 38
- Chapter 4 40
- Figure 4-1. Scanning Commands 41
- Example: Scanning With 43
- External Devices 43
- Example: Scanning 44
- "Event In" Ports 44
- Using the Scan Complete Bit 45
- Chapter 5 46
- Command Types 46
- SCPI Command Reference 48
- Subsystem Syntax ABORt 49
- • *RST Condition: ARM:COUNt 1 50
- 1 and MAX returns 32767 51
- Parameters 51
- Comments 51
- :MONitor:CARD 52
- :MONitor[:STATe] 53
- INITiate 54
- :CONTinuous? 55
- [:IMMediate] 55
- [ROUTe:] 57
- SCAN:MODE? 61
- SCAN:PORT 61
- :OPERation:ENABle 62
- :OPERation[:EVENt]? 63
- :CDEScription? 64
- :SOURce? 69
- IEEE 488.2 Common Commands 70
- Command Quick Reference 71
- 16-Channel Relay Multiplexer 72
- Specifications 72
- Relay Life 74
- End of Life Detection 74
- Replacement Strategy 74
- Appendix B 76
- Computer 77
- Configurations 77
- = 1FC000 79
- 08, is register number 4 79
- Reading the 80
- Registers 80
- Writing to the 81
- Error Messages 84
- Symbols: 86
- C (continued) 87
- Index 89 88
- 90 Index 89
- R (continued) 90
- S (continued) 91
- Index 93 92
- 94 Index 93
ASCOM OFFICE 130PRO manuals
Owner’s manuals and user’s guides for Telephones ASCOM OFFICE 130PRO.
We providing 3 pdf manuals ASCOM OFFICE 130PRO for download free by document types: Operations Instructions, User Manual, User's Guide
Commenti su questo manuale