Agilent Technologies InfiniiVision 5000 Series Manuale Utente Scaricare il pdf (Pagina 16)

Performance characteristics (continued)

Trigger system (continued)

Selections Edge,pulsewidth,pattern,TV,duration

 Edge Triggeronarising,falling,oralternatingedgeofanysource

 Pulsewidth Triggerwhenapositive-ornegative-goingpulseislessthan,greaterthan,orwithinaspecifiedrange

  onanyofthesourcechannels.

  Minimumpulsewidthsetting:

   5ns(DSO501xA)

   2ns(DSO503xA,DSO505xA)

  Maximumpulsewidthsetting:10s

Pattern Trigger at the beginning of a patternofhigh,low,anddon'tcarelevelsand/orarisingorfallingedge

  establishedacrossanyofthechannels,butonlyafterapatternhasbeenestablishedforaminimumof

  2nsec.Thechannel’shighorlowlevelisdefinedbythatchannel’striggerlevel.

 Sequence ArmonEventA,triggeronEventB(edgeorpattern),withoptiontoresetonEventCortimedelay

TV Triggerusinganyoscilloscopechannelonmostanalogprogressiveandinterlacedvideostandards

  includingHDTV/EDTV,NTSC,PAL,PAL-MorSECAMbroadcaststandards.Selecteitherpositiveor

  negativesyncpulsepolarity.ModessupportedincludeField1,Field2,allfields,alllines,oranyline

  withinafield.TVtriggersensitivity:0.5divisionofsyncsignal.Triggerholdofftimecanbeadjustedin

half field increments.

 Duration Triggeronamulti-channelpatternwhosetimedurationislessthanavalue,greaterthanavalue,

  greaterthanatimevaluewithatimeout,orinsideoroutsideofasetoftimevalues.

  Minimumdurationsetting:2ns

  Maximumdurationsetting:10s

 CAN TriggeronCAN(ControllerAreaNetwork)version2.0Aand2.0Bsignals.Triggeronthestartofframe

  (SOF)bit(standard).N5424AoptionsupportstriggeringonremoteframeID(RTR),dataframeID

  (~RTR),remoteordataframeID,dataframeIDanddata,errorframe,allerrors,acknowledgeerrorand

  overloadframe.

FlexRay Trigger on FlexRayFrames,errors,eventsandcycle-multiplexedtriggering.N5432Coroption

  FLXsupportsalsotriggeringonparticularframetypessymbolically,suchasStartupframes,Nullframe,

  Syncframe,etc.,aswellasBooleanNOTframetypes.

LIN Trigger on LIN (Local Interconnect Network) sync break at beginning of message frame (standard).

  N5424AoptionsupportstriggeringonframeID.

C Trigger on I

C (Inter-ICbus)serialprotocolatastart/stopconditionoruserdefinedframewithaddress

  and/ordatavalues.Alsotriggeronmissingacknowledge,addresswithnoacq,restart,EEPROMread,

and 10‑bit write.

SPI Trigger on SPI (SerialProtocolInterface)datapatternduringaspecificframingperiod.Supportspositive

  andnegativeChipSelectframingaswellasclockIdleframinganduser-specifiednumberofbitsper

frame.

 RS-232/UART View the informationsentoveraRS-232serialbus.Displayreal-timetime-aligneddecodeoftransmit

  andreceivelines.TheapplicationalsoenablestriggeringonRS-232/UARTconditions.

MIL‑STD 1553 Trigger on specific Command/StatusWords,DataWords,anderrorconditions.

AutoScale Findsanddisplaysallactivechannels,setsedgetriggermodeonhighest-numberedchannel,sets

  verticalsensitivityonchannels,timebasetodisplay~1.8periods.Requiresminimumvoltage>

  10mVpp,0.5%dutycycleandminimumfrequency>50Hz.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22 23

Commenti su questo manuale

Nessun commento

Agilent Technologies InfiniiVision 5000 Series Manuale Utente Pagina 16

Commenti su questo manuale

Prodotti e manuali riguardandi Misurazione, test & controllo Agilent Technologies InfiniiVision 5000 Series