Agilent Technologies E1330B Manuale Utente Pagina 122
- Pagina / 156
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
120 Agilent E1330B Digital I/O Module Register Information
Appendix B
A Register-Based Input Algorithm
The following algorithm describes the procedure you use to program the registers
to read a byte of data from a peripheral. The algorithm follows a flag-driven input
procedure initiated by the computer. The computer polls the Digital I/O module to
see if the data has been transmitted by the peripheral by checking the Port
Transfer/Control Register, bit 0 (referred to as the acknowledge flag - hence, the
name flag-driven). Once the flag is TRUE the computer can read new data from the
port. The actual path followed by the peripheral and the Digital I/O module to set
this bit is controlled by the handshake mode you select.
- *E1330-90007* 1
- Contents 3
- 2 Contents 4
- Contents 3 5
- 4 Contents 6
- Certification 7
- Safety Symbols 8
- WARNINGS 8
- Documentation History 8
- DECLARATION OF CONFORMITY 9
- Getting Started 13
- 12 Getting Started 14
- Chapter 1 14
- Table 1-1. Data Lines 14
- Instrument Definition 15
- Downloading SCPI Drivers 15
- SCPI Command 16
- Format Used in This 16
- Specifying SCPI 16
- Commands 16
- Specifying Multiple Port 17
- Operations 17
- Initial Operation 18
- Chapter 2 19
- Using This Chapter 19
- Setting the Address Switch 20
- Enabling Pull-ups 21
- Selecting the Interrupt Line 22
- Combining the Flag Lines 23
- Using with External Pull-ups 30
- Typical Connection 31
- Chapter 3 33
- Addressing the Module 33
- Operation Overview 34
- Default and Reset States 35
- Setting the Polarity 35
- Setting the Handshake Mode 36
- Inputting Data Bytes and Bits 37
- Multiple Port Operations 39
- Using Trace Memory 40
- I/O Module 43
- The CTL Line 44
- Using the Handshake Modes 46
- Chapter 4 47
- 0 or 1. Byte or 53
- Multiple Port 56
- Input/Output 56
- Command Reference 59
- SCPI Command Reference 62
- DISPlay Subsystem 63
- :MONitor[:STATe]? 65
- MEASure Subsystem 66
- Parameters 67
- Comments 69
- MEMory Subsystem 70
- :VME:STATe 73
- • *RST Condition: Set to OFF 73
- :VME:STATe? 73
- [SOURce:] Subsystem 74
- 0.000002. MAX returns 0.015 81
- DIGital:DATAn[:type]:POLarity 84
- DIGital:DATAn[:type]:TRACe 85
- DIGital:FLAGn:POLarity 88
- DIGital:FLAGn:POLarity? 88
- DIGital:TRACe:DEFine? 94
- DIGital:TRACe:DELete:ALL 94
- DIGital:TRACe:DELete[:NAME] 94
- STATus Subsystem 95
- :OPERation:CONDition? 96
- :OPERation:ENABle 96
- :OPERation:ENABle? 96
- :OPERation[:EVENt]? 96
- :QUEStionable:CONDition? 97
- :QUEStionable:ENABle 97
- :QUEStionable:ENABle? 97
- :QUEStionable[:EVENt]? 97
- SYSTem Subsystem 98
- • Related Commands: *ERR 99
- • *RST Condition: None 99
- :VERSion? 99
- IEEE 488.2 Common Commands 100
- Command Quick Reference 101
- Chapter 5 104
- Appendix A 105
- Information 107
- A16 Address Space 108
- Outside the Command 108
- Module or Mainframe 109
- Inside the Command 109
- Reset and Registers 111
- Register Definitions 111
- Appendix B 112
- Register Descriptions 113
- Port Interrupt 114
- Control Register 114
- Port Transfer 115
- Port Control/ 116
- Status Register 116
- Port Handshake 118
- Register 118
- Table B-4. Handshake Type 119
- Table B-5. Range Multipliers 119
- Port Normalization 120
- Programming Examples 123
- Resetting the 124
- Reading the 125
- ID, Device 125
- Type, and 125
- Registers 125
- C Version 126
- Writing an 127
- 8-Bit Byte 127
- Writing a 129
- 16-Bit Word 129
- Reading an 130
- PIR Interrupts 133
- Agilent E1330 133
- B Non-data 138
- Line I/O 138
- Embedded 142
- Computer 142
- Error Messages 145
- 144 Error Messages 146
- Appendix C 146
- Agilent E1330B User’s Manual 147
- 146 Index 148
- C (continued) 149
- 148 Index 150
- I (continued) 151
- M (continued) 152
- P (continued) 153
- R (continued) 154
- S (continued) 155
Prodotti e manuali riguardandi Multimetri Agilent Technologies E1330B
Multimetri Agilent Technologies 8481B Specifiche
(34 pagine)
(34 pagine)
Multimetri Agilent Technologies 83630A Specifiche
(133 pagine)
(133 pagine)
Multimetri Agilent Technologies 34411A Guida Utente
(152 pagine)
(152 pagine)
Multimetri Agilent Technologies 8487D Guida Utente
(196 pagine)
(196 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale