Agilent Technologies 222A Manuale delle Istruzioni Pagina 86
- Pagina / 123
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
86
Programming Reference
SCPI Instrument Command List
Command :TRIG:LEV
Long
:TRIGger:LEVel
Form Set & Query
Parameter Numeric
Parameter Suffix
V
with engineering prefixes.
*RST value 1.0 V
Specified Limits –10 V to +10 V
Description Use this command to program the triggering threshold of the CLK-IN
connector.
Example To set the input impedance and the threshold of the CLK-IN connector:
Command :TRIG:SLOP
Long
:TRIGger:SLOPe
Form Set & Query
Parameter
POSitive | NEGative
*RST value
POS
Description Use this command to select the trigger slope for the pulse period
triggering signal applied to the CLK-IN connector.
Command :TRIG:SOUR
Long :TRIGger:SOURce
Form Set & Query
Parameter
IMMediate | INTernal[1] | INTernal2 | EXTernal2
*RST value
IMM
Description Use this command to select the pulse period source of the
Agilent 81101A by selecting the source of the pulse period trigger signal:
:TRIG:IMP 50OHM
:TRIG:LEV 2.5V
:TRIG:SOUR EXT2
Set CLK-IN impedance to 50
Ω
Set CLK-IN threshold to 2.5V
Pulse period trigger from CLK-IN
- Reference Guide 1
- Agilent 81101A 50 MHz 3
- Pulse Generator 3
- Copyright 4
- Warranty 4
- Limitation of Warranty 5
- Exclusive Remedies 5
- Certification 5
- Services and Support 5
- Safety Summary 6
- Ground the Instrument 7
- Safety Symbols 8
- About this Book 9
- Conventions Used in this Book 10
- Contents 11
- 1General Programming 13
- The GP-IB Interface Bus 14
- Agilent 81101A Remote Control 15
- Programming Recommendations 16
- Common Command Summary 18
- Status Model 19
- Condition Register 20
- Transition Filters 20
- Event Register 20
- Enable Register 21
- Status Byte 22
- Standard Event Status Group 22
- OPERation Status Group 23
- QUEStionable Status Group 24
- 2Programming Reference 25
- Agilent 81101A SCPI Command 26
- Programming Reference 31
- Programming the Instrument 35
- Continuous 36
- Triggered 36
- External Width 37
- SCPI Instrument Command List 38
- :DISPlay[:WINDow][:STATe] 43
- DISP OFF 43
- :MMEMory:CATalog? 44
- :MMEMory:CDIRectory 44
- :MMEMory:COPY 45
- :MMEMory:DELete 45
- :MMEMory:INITialize 45
- :MMEMory:LOAD:STATe 46
- :MMEMory:STORe:STATe 46
- :OUTPut[1][:NORMal][:STATe] 47
- :OUTP ON 47
- :OUTPut[1]:IMPedance:EXTernal 47
- :OUTPut[1]:POLarity 48
- Amplitude = High – Low 50
- Offset = 50
- High – Low 50
- Period = 54
- Frequency 54
- [:SOURce]:HOLD 55
- [:SOURce]:PHASe[1][:ADJust] 56
- [:SOURce]:PULSe:DCYCle[1] 57
- [:SOURce]:PULSe:DELay[1] 57
- [:SOURce]:PULSe:DELay[1]:HOLD 58
- [:SOURce]:PULSe:DELay[1]:UNIT 59
- DblDel% = 60
- Frequency = 62
- [:SOURce]:PULSe:PERiod:AUTO 63
- [:SOURce]:PULSe:TDELay[1] 63
- [:AMPlitude] 67
- [:SOURce]:PULSe:WIDTh[1] 68
- [:SOURce]:ROSCillator:SOURce 68
- Amplitude 70
- Offset = 72
- High–Low 73
- :STATus:PRESet 76
- :SYSTem:CHECk[:ALL][:STATe] 78
- :SYSTem:ERRor? 78
- :SYSTem:KEY 79
- :SYSTem:PRESet 81
- :SYSTem:SECurity[:STATe] 82
- :SYSTem:SET 83
- :SYSTem:VERSion? 83
- :SYSTem:WARNing[:COUNt]? 83
- :SYSTem:WARNing:STRing? 84
- :SYSTem:WARNing:BUFFer? 84
- :TRIGger[:SEQuence[1]]:COUNt 84
- :TRIGger:IMPedance 85
- :TRIGger:LEVel 86
- :TRIGger:SLOPe 86
- 3Specifications 89
- Manufacturer 90
- Supplementary 90
- Information 90
- Agilent 81101A Specifications 91
- Recalibration period 92
- Acoustic Noise Emission 92
- Timing Specifications 93
- Transition Times 95
- Level Specifications 96
- Clock Sources 97
- Clock / PLL Reference Input 98
- Phase Locked Loop (PLL) 98
- Output Modes 99
- Trigger Modes 100
- Trigger Output 101
- Strobe Output 101
- Typical Delays 102
- Human Interface 103
- Remote Control 104
- Pulse Parameter Definitions 105
- Time Reference Point 106
- Pulse Period 106
- Trigger Delay 106
- Pulse Width 106
- Pulse Delay 107
- Double Pulse Delay 107
- Interchannel Delay (Skew) 107
- Transition Time 108
- Linearity 108
- Stability 109
- Pulse Levels 109
- Preshoot, Overshoot, Ringing 110
- Settling Time 110
- Repeatability 111
- Specifications 112
- Front Panel Controls 117
- Edition E0300 118
- Printed in Germany 118
- 81101-91021 118
- DECLARATION OF CONFORMITY 123
Prodotti e manuali riguardandi Misurazione, test & controllo Agilent Technologies 222A
(24 pagine)
(18 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale