Agilent Technologies 81134A Manuale di Servizio Pagina 32
- Pagina / 104
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
SCPI Commands Reference DIGital Commands
32 Agilent 81133A/81134A Pulse Generator Programming Guide, March 2007
Example Set data format to R1.
:DIG:SIGN:FORM R1
:DIGital[1|2][:STIMulus]:SIGNal:POLarity
Syntax
:DIG[1|2][:STIM]:SIGN:POL[?]
Form Set & Query
Description This command is used to program the data polarity for Data and
PRBS signals. The 32- bit data pattern is logically inverted, that is,
1 s are replaced with 0 s and vice versa.
NOTE This is not the same as the
[:SOURce][:PULSe]:POLarity[1|2]
command, which physically inverts the signal by swapping the
OUTPUT and
OUTPUT signals.
Parameter NORMal|COMPlement|INVerted
INVerted are synonyms (INVerted is included for backwards
compatibility).
*RST value NORMal
Example Logically invert the 32- bit data.
:DIG:SIGN:POL INV
:DIGital[1|2][:STIMulus]:SIGNal:
CROSsover:[VALue]
Syntax
:DIG[1|2][:STIM]:SIGN:CROS[?]
Form Set & Query
Description If variable crossover mode is enabled, this command specifies a
value to adjust the crossover point of the NRZ signal in PRBS or
data mode, individually for each channel.
To enable the variable crossover mode, use
“:DIGital[1|2][:STIMulus]:SIGNal: CROSsover:[STATe]” on page 34.
The variable crossover is used to artificially close the eye pattern,
which simulates distortion.
- Programming Guide 1
- Important Notice 2
- About This Programming Guide 3
- Contents 5
- OUTPut Commands 39 6
- SOURce Commands 45 6
- Status Handling Commands 67 6
- Troubleshooting 97 7
- Introduction 10
- SCPI Commands Reference 17
- Common Commands 19
- Standard Settings 21
- DIAGnostic Commands 23
- :CAL:TIM 24
- DIGital Commands 25
- Range Maximum Pattern Length 29
- 60 – 3360 Mhz 12 Mbit 29
- 30 – 60 Mhz 6 Mbit 29
- 15 – 30 Mhz 3 Mbit 29
- CROSsover:[VALue] 32
- CROSsover:[STATe] 34
- DISPlay Commands 35
- MEASure Commands 36
- :MEASure:FREQuency? 37
- :MEASure:PERiod? 38
- OUTPut Commands 39
- :OUTPut[0 41
- :OUTPut0:SOURce 42
- :OUTPut[0 43
- :OUTPut[1 43
- :OUTPut[1 44
- :OUTPut:CENTral 44
- SOURce Commands 45
- [:SOURce]:FUNCtion[:SHAPe] 50
- [:SOURce]:FUNCtion:MODe[1 51
- [:SOURce]:PHASe[:ADJ][1 53
- [:SOURce][:PULSe]:DCYCle[1 54
- [:SOURce][:PULSe]:DELay[1 55
- [:SOURce][:PULSe]:DESKew[1 56
- [:SOURce][:PULSe]:DHOLd[1 56
- [:SOURce][:PULSe]:PERiod 57
- [:SOURce][:PULSe]:WIDTh[1 58
- [:SOURce]:PM[1 59
- [:SOURce]:PM[1 59
- [:IMMediate][:AMPLitude] 60
- [:IMMediate]:OFFSet 61
- [:IMMediate]:HIGH 62
- [:IMMediate]:LOW 63
- [:IMMediate]:TERM 64
- [:SOURce]:VOLTage[1 64
- [:AMPLitude]? 64
- Status Handling Commands 67
- :STATus:OPERation 70
- :STATus:PRESet 70
- :STATus:QUEStionable 71
- :STATus:QUEStionable:VOLTage 73
- :STATus:QUEStionable:MONotony 76
- SYSTem Commands 79
- :SYSTem:ERRor? 81
- :SYSTem:PRESet 81
- :SYSTem:SET 82
- :SYSTem:VERSion? 82
- :ADDRess 84
- :DGATeway 85
- TRIGger Commands 86
- :TRIGger:SOURce 87
- :TRIGger:TERM 88
- :TRIGger:TERM:STATE[?] 89
- ARM Commands 90
- :ARM[:SEQuence][:LAYer]:LEVel 91
- :ARM[:SEQuence][:LAYer]:SLOPe 92
- :ARM[:SEQuence][:LAYer]:TERM 94
- :ARM[:SEQuence][:LAYer]:STOP 95
- Troubleshooting 100
- 5988-7402EN 104
Prodotti e manuali riguardandi Misurazione, test & controllo Agilent Technologies 81134A
(344 pagine)ASCOM OFFICE 130PRO manuals
Owner’s manuals and user’s guides for Telephones ASCOM OFFICE 130PRO.
We providing 3 pdf manuals ASCOM OFFICE 130PRO for download free by document types: Operations Instructions, User Manual, User's Guide
Commenti su questo manuale