Agilent-technologies Multiple Channel Controller 85330A Manuale Utente Pagina 27
- Pagina / 166
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
85330A Multiple Channel Controller 1-9
Installation
Selecting Positive or Negative-Edge Event Triggers
Figure 1-4 Positive/Negative-Edge EVENT TRIG jumpers
1. Remove the two screws that hold the E1330B board in place.
2. Remove the four screws that hold the 85330-60002 board in place.
3. Pull out the two boards at the same time. You can do this by pulling each
one out a little at a time, until they are both removed. Place the boards
on an anti-static surface.
Standard positive-edge operation is set at the factory by jumpering
E9 and E10 together.
4. To select negative-edge operation, move the jumper across E9 and E8.
5. Reinstall the boards and screws.
- Agilent Technologies 85330A 1
- Multiple Channel Controller 1
- Restricted Rights Legend 2
- Warranty 4
- Service and Support 5
- Instrument Markings 6
- Safety Earth 7
- Manufacturers Declaration 9
- DECLARATION OF CONFORMITY 10
- Typeface Conventions 11
- Contents 13
- 1 Installation 19
- Choosing the Proper 20
- Installation 21
- Controller 24
- Procedure 25
- Triggers 26
- • SCU address is set to 0 28
- 2 Performance Verification 31
- Recommended 32
- Equipment 32
- Performance Verification Test 33
- Setting Up the Equipment 33
- Measurement Display 35
- Performance Verification 36
- Pulse Receive and 38
- Cycle Test 38
- Counter Pulse Delay 39
- 12. Remove the BNC cables 40
- Measurement Busy 41
- Signal and Pulse 41
- Width Test 41
- Verifying the RF Switches 43
- • Jumper (see below) 45
- • Soldering iron 45
- • 2 jumper wires 45
- AUX 1 and AUX 2 47
- Output Voltage Test 48
- When Finished with 48
- All Tests 48
- 3 Operator’s Check 49
- Operator’s Check 50
- 4 General Information 51
- Measurement Speed Advantages 52
- Triggering 52
- • Perform service functions 53
- Switch control units 54
- The Downloadable 55
- • Option 001: 1 meter 56
- • Option 002: 2 meters 56
- • Option 005: 5 meters 56
- • Option 010: 10 meters 56
- • A switch control unit (SCU) 57
- General Information 58
- Characteristics 59
- Ventilation 60
- Requirements 60
- Dimensions 60
- Need More 61
- Information 61
- Rear Panel Features 62
- SWITCH PORT 1 and 2 64
- AUX POWER IN 64
- 85330A Compatibility 65
- 5 Manual Operation 67
- To Use the Front Panel 68
- Softkey Map 69
- Changing the GPIB 70
- (to select a channel) 71
- Manual Operation 72
- To Perform Service Functions 73
- 6 Programming 75
- Definition of Terms 76
- • CW Measurement Configuration 77
- • 8530A Control of Sources 77
- • Fast Source Control 77
- CW Measurement Configuration 78
- To Use this 79
- 85330A settings 80
- 8530A Control of Sources 81
- Fast Source Control 82
- To Use Direct Control 83
- In this example: 85
- To Use Run-Time Control Mode 86
- TTL Trigger and 87
- Ready Timeouts 87
- Select Switch State 88
- Event Trigger 89
- Receiver Ready 89
- Switch List Loop 89
- Frequency Loop 91
- Event Loop 91
- Programming 100
- Programming Examples 100
- 85330A Error Messages 108
- 7 Remote Programming Command 111
- Parameters 112
- Abbreviated Commands 112
- Common Commands 113
- Syntax *OPC? 114
- Syntax *RST 114
- Example OUTPUT 70918;”*RST” 114
- Standard Command Reference 115
- ROUTe:CLOSe 115
- ROUTe:CONTrol 116
- ROUTe:DELay 116
- Subsystem Command Syntax 117
- :INITiate 117
- :TIMEout 117
- RUNTime:CONTroller 118
- RUNTime:EVENt:COUNt 118
- RUNTime:EVENt:TRIGger 119
- RUNTime:INITiate:IMM 120
- RUNTime:SOURce:COUNt 120
- RUNTime:SWITch:DELay 122
- RUNTime:SWITch:SCAN 123
- RUNTime:SWITch:TRIGger 124
- RUNTime:TIMEout:EVENt 125
- RUNTime:TIMEout:RECeiver 125
- RUNTime:TIMEout:REMote 126
- RUNTime:TIMEout:SOURce 126
- SYSTem:ERRor? 127
- 8 In Case of Difficulty 129
- In Case of Difficulty 130
- 9 Service 131
- Theory of Operation 132
- GPIB 133
- Recommended Test Equipment 137
- Troubleshooting 139
- 85383A Local Control Cable 141
- 85383B Expansion Cable 141
- 85384A Switch Driver Cable 141
- 85385A Remote Trigger Cable 141
- Table 9-5 85385A Wiring 142
- Replaceable Parts 143
- Mainframe, Plug-in 145
- Switch Control Unit 146
- RF Switch 146
- Interconnect Cables 147
- Assembly and Disassembly 148
- E1330 Card 149
- Configuration 149
- 85330-60002 Card 149
- Disassembly 150
- Assembly 150
- Adjustments 151
- Selecting the Multiple 152
- Channel Controller’s 152
- GPIB Address 152
- Switching from the 153
- Internal to External 153
- Power Supply 153
- Preventive Maintenance 154
- 10 Accessory Documentation 156
- Accessory Documentation 157
- A Glossary 158
- • Attaching cables 159
- Glossary 160
- Standard System 162
- Switch Address 162
- Switch Module 162
- Numerics 164
Prodotti e manuali riguardandi Hardware Agilent-technologies Multiple Channel Controller 85330A
Hardware Agilent-technologies N2620A Manuale Utente
(279 pagine)
(279 pagine)
Hardware Agilent-technologies 85225F Manuale Utente
(148 pagine)
(148 pagine)
Hardware Agilent-technologies N9340A Manuale Utente
(161 pagine)
(161 pagine)
Hardware Agilent-technologies N2610A Manuale Utente
(248 pagine)
(248 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale