Agilent Technologies Ininiium 9000 Guida Utente Pagina 63
- Pagina / 112
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Using the Oscilloscope
Graphical User Interface
3-27
Run/Stop Control See figure 3-11. At the left side of the bar are four icons:
• The leftmost is a blue-green octagon. Clicking on this starts an acquisition. (Same
as pressing the Run key on the front panel.)
• The next control is a red octagon. Clicking on this stops acquisition. (Same as
pressing the Stop key on the front panel.)
• The next control is a small windshield wiper. Clicking on this clears acquired
waveform data from the display. (Same as pressing the Clear Display key on the
front panel.)
• The next control is a printer. Clicking prints the screen to the default printer.
• The rightmost control is the waveform brightness control.
Horizontal settings and controls The middle of the bar contains the horizontal
settings and controls. Leftmost is a button, labeled with an “H.” Clicking on this
will display the horizontal setup dialog box.
Next is the current horizontal scale. Clicking on this displays a pop-up numeric
keypad so you can set a particular horizontal scale. Or, you can click on the two icons
to the right of the horizontal scale setting to cycle through the preset speeds. The left-
hand icon shrinks the waveform, which decreases the horizontal scale and increases
the time per division. The right-hand icon stretches the waveform, which increases
the horizontal scale and decreases the time per division.
Next is the horizontal position (delay) setting. Clicking on this displays a pop-up
numeric keypad that allows you to set a particular position. Or, you can use the three
icons to the right. The left arrow moves the waveform to the left, the center “0” resets
the delay to zero, and the right arrow moves the waveform to the right.
Across the toolbar are three vertical arrows. These are the left, center, and right
horizontal reference indicators. Clicking on one of these arrows moves the horizontal
position to the respective horizontal reference position on the display—left, center,
or right. Assuming the horizontal position is at zero:
• Left means the information on the display is all post-trigger.
• Center means the information to the left of center is pretrigger; to the right is post-
trigger.
• Right means the information on the display is pretrigger.
The horizontal position value represents the time relative to the trigger at the
respective horizontal reference. When you change the horizontal scale, the
waveforms expand and contract about this reference position.
Trigger settings and controls The right side of the bar contains the trigger
settings and controls. These will vary depending on the current trigger
configuration, which can be set using the front panel and the graphical interface.
Advanced trigger configuration items are available only through the graphical
interface. You can click on the button labeled with a “T” to bring up the trigger
- Infiniium 9000A Series 1
- Oscilloscope 1
- In This Book 2
- Contents 3
- To inspect package contents 7
- Setting Up the Oscilloscope 10
- Technical Specifications 12
- Figure 1-1 18
- To connect power 19
- Side Panel 21
- Probing the Circuit 23
- Figure 1-5 24
- To turn on the oscilloscope 25
- To turn off the oscilloscope 26
- To clean the oscilloscope 31
- Working in Comfort 33
- Introduction 34
- Mice and Other Input Devices 36
- Using the Oscilloscope 37
- Using the Front Panel 39
- Front Panel 40
- Run Controls 42
- Horizontal Controls 42
- Trigger Controls 42
- Vertical Controls 43
- To clear the waveform display 46
- To use the markers 53
- To use the quick measurements 54
- Using the Graphical Interface 57
- Graphical User Interface 58
- Tab Display Area 61
- Minimize and maximize 61
- Tab area 61
- Figure 3-5 66
- Figure 3-6 67
- Figure 3-7 68
- 1 Click on a menu bar item 69
- Figure 3-9 71
- Figure 3-10 72
- Start and Stop Icons 73
- Click this 73
- Click this button 73
- To print the screen 75
- To change waveform brightness 76
- To turn a channel on or off 77
- To adjust the vertical offset 78
- Figure 3-16 79
- To adjust vertical scaling 80
- To access the channel setup 81
- To adjust horizontal scale 83
- To adjust horizontal position 84
- Figure 3-23 87
- 1 Turn on the markers 88
- Figure 3-24 89
- Figure 3-25 91
- To access the trigger setup 92
- To set an edge trigger 93
- To set dialog box preferences 94
- Figure 4-1 99
- Access Methods 100
- Figure 4-2 100
Prodotti e manuali riguardandi Misurazione, test & controllo Agilent Technologies Ininiium 9000
(18 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale