Agilent Technologies 85032B/E 50 Specifiche Pagina 44
- Pagina / 269
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Performance Checks 8712ET/ES and 8714ET/ES
Specifications RF Network Analyzers
1-36 Service Guide
Specifications
Definitions
All specifications and characteristics apply over a 25 °C ±5 °C range (unless otherwise
stated) and sixty minutes after the instrument has been turned on.
Specification (spec.): Warranted performance. Specifications include guardbands to
account for the expected statistical distribution, measurement uncertainties, and changes
in performance due to environmental conditions.
Characteristic (char.): A performance parameter that the product is expected to meet
before it leaves the factory, but is not verified in the field and is not covered by the product
warranty. A characteristic includes the same guardbands as a specification.
Typical (typ.): Expected performance of an average unit which does not include
guardbands. It is not covered by the product warranty.
Nominal (nom.): A general descriptive term that does not imply a level of performance. It
is not covered by the product warranty.
Calibration: The process of measuring known standards from a calibration kit to
characterize the systematic (repeatable) errors of a network analyzer.
Corrected (residual) Performance: Indicates performance after error correction
(calibration). It is determined by the quality of calibration standards and how well
“known” they are, plus system repeatability, stability, and noise.
Uncorrected (raw) Performance: Indicates instrument performance without error
correction. The uncorrected performance affects the stability of a calibration.
- Service Guide 1
- Certification 2
- Documentation Map 3
- Contents 5
- 1 Performance Checks 9
- RF Network Analyzers 10
- 1-2 Service Guide 10
- Equipment List 11
- 6. Press 13
- 7. Press 13
- Service Guide 1-7 15
- Trigger Hold 17
- Performance Test Software 18
- Estimated Time 19
- Equipment 20
- File Structure 21
- Configuration File 22
- Getting Started 23
- Configuration Menu 24
- Service Guide 1-17 25
- 1-18 Service Guide 26
- CAL DATA ENTRY 26
- Using the Program 27
- Test Selection Menu 29
- Additional Information 30
- PRINT RESULTS 31
- PT01: Frequency Accuracy 32
- PT02: Gain Compression 33
- PT03: Noise Floor 34
- PT04: Dynamic Accuracy 35
- PT05: Power Flatness 36
- PT06: Absolute Power Accuracy 37
- 1-30 Service Guide 38
- PT08: Directivity 39
- 1-32 Service Guide 40
- PT09: Harmonics 41
- PT10: Trace Noise 42
- PT11: Crosstalk 43
- Specifications 44
- System Performance 45
- Service Guide 1-39 47
- Service Guide 1-41 49
- Service Guide 1-43 51
- Service Guide 1-45 53
- Service Guide 1-47 55
- Service Guide 1-49 57
- Service Guide 1-51 59
- Service Guide 1-53 61
- Service Guide 1-55 63
- Test Port Output 65
- Service Guide 1-59 67
- Test Port Input 71
- Service Guide 1-65 73
- Service Guide 1-67 75
- Service Guide 1-69 77
- 1. Narrowband detection mode 78
- Service Guide 1-71 79
- General Information 81
- Service Guide 1-75 83
- Service Guide 1-77 85
- 1-78 Service Guide 86
- Features 87
- Data Markers 88
- Marker Functions 88
- Internal Memory 88
- Disk Drive 88
- Network File System (NFS) 88
- Data Hardcopy 89
- Automation 89
- Measurement Calibration 90
- Calibration Interpolation 91
- Available Calibrations 91
- Calibration Kits 92
- Test Sets 93
- 2Adjustments 94
- 2-4 Service Guide 97
- Frequency Accuracy Adjustment 98
- Required Equipment 100
- Procedure 100
- In Case of Difficulty 101
- Service Guide 2-9 102
- SYSTEM OPTIONS 117
- 2-24 Service Guide 117
- 3Assembly Replacement 119
- Introduction 120
- Service Guide 3-3 121
- 3-4 Service Guide 122
- Service Guide 3-5 123
- 3-6 Service Guide 124
- Service Guide 3-7 125
- 3-8 Service Guide 126
- Service Guide 3-9 127
- 3-10 Service Guide 128
- Removing the Source Assembly 129
- 3-12 Service Guide 130
- Service Guide 3-13 131
- 3-14 Service Guide 132
- Removing the Coupler 133
- Installing the Coupler 134
- Installing the Switch 134
- Installing the Attenuator 135
- Installing the Limiter 136
- Service Guide 3-19 137
- Removing the Display Assembly 138
- Service Guide 3-21 139
- 3-22 Service Guide 140
- Service Guide 3-23 141
- How to Order Parts 142
- 8712ET/ES and 8714ET/ES 143
- Service Kit 145
- How to Use the Extender Board 146
- Initializing 147
- Operator's Check 148
- Check the Rear Panel LEDs 149
- 4-8 Service Guide 150
- Removing the Assemblies 151
- Error During Power-up 152
- Test Status LEDs 153
- 4-12 Service Guide 154
- Service Guide 4-13 155
- Service Guide 4-15 157
- Coefficients 158
- Front Panel Problems 159
- Other Power-Up Problems 159
- Other Error Messages 159
- 4-18 Service Guide 160
- Service Guide 4-19 161
- 4-20 Service Guide 162
- Service Guide 4-21 163
- 4-22 Service Guide 164
- Service Guide 4-23 165
- 4-24 Service Guide 166
- Service Guide 4-25 167
- 4-26 Service Guide 168
- Service Guide 4-27 169
- 4-28 Service Guide 170
- Service Guide 4-29 171
- Service Guide 4-31 173
- Mechanical Problems 175
- Receiver Detector Problems 175
- Service Guide 4-35 177
- 4-36 Service Guide 178
- RF Power Problems 179
- DIN Keyboard 180
- RS-232 Printers and Plotters 180
- Floppy Disk Drive Maintenance 180
- GPIB Systems 181
- LAN Troubleshooting 182
- Service Guide 4-41 183
- Testing between Two Analyzers 184
- 0.0.0.0 and 185
- LAN State ON off 185
- Service Guide 4-47 188
- 4-48 Service Guide 189
- 5Service Related Menus 190
- Figure 5-1 Service Key Menus 192
- Tests and Adjustments Menu 193
- Select Self-Test Menu 194
- Select Adjustment Menu 197
- Instrument Info 199
- Update Corr Const Menu 200
- Service Utilities Menu 1 201
- Meas Cal Options Menu 204
- Analog Bus Menu 205
- Service Guide 5-17 206
- Service Utilities Menu 2 208
- Service Utilities Menu 3 209
- Service Guide 5-21 210
- 5-22 Service Guide 211
- Syntax Summary 212
- Softkey SCPI Commands 212
- <num> 213
- Service Guide 5-25 214
- 6Theory of Operation 216
- System Theory 218
- 6-4 Service Guide 219
- Service Guide 6-5 220
- Power Supply (A6) 221
- Digital Control Group 221
- Display Assembly (A7) 222
- Source Group 223
- Service Guide 6-9 224
- Controlling Spurs 225
- Service Guide 6-11 226
- Receiver Assembly (A5) 227
- RF Path of the ET Analyzer 228
- Limiters 229
- Service Guide 6-15 230
- RF Path of the ES Analyzer 231
- 7Parts List 232
- Analyzer Hardware 233
- Parts” on page 3-24 234
- Service Guide 7-5 236
- Description 237
- HP/Agilent 237
- Part Number 237
- Service Guide 7-7 238
- Service Guide 7-9 240
- 7-10 Service Guide 241
- Service Guide 7-11 242
- 7-12 Service Guide 243
- 7-14 Service Guide 245
- Service Guide 7-17 248
- Service Guide 7-19 250
- Service Guide 7-21 252
- 8-2 Service Guide 254
- Service Guide 8-3 255
- In Case of Difficulties 256
- Obtaining Firmware 258
- Safety Symbols 260
- General Safety Considerations 261
- Lithium Battery Disposal 262
- Warranty 263
- Assistance 264
- Shipment for Service 264
- Service Guide 9-7 265
- Index Index-1 266
- 2-Index Index 267
- Index Index-3 268
- 4-Index Index 269
Prodotti e manuali riguardandi Misurazione, test & controllo Agilent Technologies 85032B/E 50
Misurazione, test & controllo Agilent Technologies InfiniiVision 5000 Series Manuale Utente
(23 pagine)
(23 pagine)
Misurazione, test & controllo Agilent Technologies Ininiium 9000 Guida di Configurazione
(28 pagine)
(28 pagine)
Misurazione, test & controllo Agilent Technologies HP 70903A IF SECTION Manuale di Servizio
(51 pagine)
(51 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale